Ge-monogram ZIF36N RH Manuale Utente

GE Monogram®36" Refrigeratorsand 36" FreezersCustomOptions GuideandInstallationInstructionsWith Custom Pas ifimenstions

10ZIR36N RefrigeratorZIF36N Freezer• The ZKTR36LH (or ZKTR36RH) trim kit installedtogether with a ZKHTR1 custom handle kit provides for the installati

23 5/16"84"2 5/16"24 3/4"84"3 3/4"23 9/16"84"2 9/16"Trim111/4" Side PanelsInsert end of side panel i

12ToolsRequired• Tinsnips to cut banding• Stepladder• 1-1/4" open-end wrench• Bucket• Level• Appliance Hand Truck• Tubing cutter• 7/16" open

13• Remove outer carton.– Carefully cut banding at the top and bottom.• Slide out back corner posts (2).• Slide carton off top of cabinet.NOTE: IT IS

14Step 2InstallWater Line• Install optional water filter in the water line near therefrigerator. A water filter is recommended in areaswhere water sup

15Step 3Install Side Panels• Side panels are not required when the refrigerator orfreezer is installed into an enclosure. Skip this step ifyou are ins

16Step 5LevelRefrigeratoror FreezerAll models have 4-point leveling. The front is supportedby leveling legs, the rear is supported by wheels.• Adjust

17Step 9CheckPower• Check to make sure power is on by opening the doorto see if interior lights are on.If you are using a 3/4" thick custom panel

18Step 13StartIcemaker• A standard toekick is supplied. Install with 2 screwsprovided, adjust to desired height and tighten screws.IMPORTANT: The vent

19This kit provides optional side trim pieces for the original grille panel frame to fit 83-1/2" and 84-1/2"installation heights.To change

CAUTIONBefore you begin – Read these instructions completely and carefully.IMPORTANT – Save these instructions for local inspector’s use.IMPORTANT – O

20Tools and materials required:• #2 Phillips screwdriver• Drill and appropriate bits• Custom door panel• Custom Handle• Safety glassesParts List:A. Ha

21Step 2 Locate handleposition• Determine the desired location of the custom handleand mark centerlines of the screw holes.• Drill 1/16" pilot ho

22Right hand door swing models are illustrated in theseinstructions. Follow these instructions for left handmodels. Tools and materials required:• #2

23Step 2 Install 3/4" trimStep 3Apply panelsupportbrackets• Attach the new 3/4" trim pieces on the top, hinge sideand bottom using original

24Step 5InstallhandlesStep 6Adjustgrille panel height• Install new door handle using original screws.• Secure the grille panel support to the back sid

25Step 8Installgrille panel• Install four of the six larger undercut screw so that the top of the screws are 1/16" from the surface of the suppor

263/4" custom door panel must be routed to accommodatethese door handle extrusions. Rout the panel asillustrated, 1/4" deep, and 1-13/16&quo

27• Place the prepared 3/4" custom door panel on the bottom trim with support bracket tabs inserted intotrim slots.• Push the panel back against

28Step 4Mount assembledpanel• Place assembled panel onto the bottom trim with support bracket tabs inserted into slots.• Push the panel back against t

29Step 1Remove handleRight hand door swing models are illustrated in theseinstructions. Follow these instructions for left hand models.NOTE: It is bes

3Design Information36" Refrigerators, FreezersFlush orSemi-FlushEnclosureInstallationsSide Panel Requirements:• Side panels are not required when

30Step 2Matchhandle extrusionsto handleFOR CUSTOM WOODPANELSSee Step 2A for Stainless Steel panels• Cut a piece of corrugated to use as a pad to prote

31Step 3Installstandoffsonto handles• Place a handle standoff onto each attachment postalong the handle. Position the set screw hole on thestandoff to

32Raised Panel on 1/4" Thick Backing:A raised panel design secured to a 1/4" thick backing(screwed or glued) can be used with this handle ki

33Before you begin:Right hand door swing models are illustrated in theseinstructions. Follow these instructions for left hand models.This kit provides

34Step 1Match HandleExtrusionto Panel• Cut a piece of corrugated to use as a pad to protectthe panel finish. Additional material may be required to pr

35This kit provides for the installation of a 3/4" thick custom grille panel to span the combined width of aside by side installation. Use this k

36• Cut a 2"x4" block, 71" long. Secure the 2"x4" to the 4mounting brackets provided using #12 or #14 woodscrews.• Secure the

StudSpacerBlockRefrigerator CabinetDoor37Step 5Install Center Trim Strip• Open doors fully.• Starting at the top, press trim strip over inside casetri

38Step 7InstallGrille Base Cover• Open doors fully.• Install the double width grille base cover byslipping the notched ends over the hinges.• Place wi

39Step 9InstallSoffitVent Top• Separate the top and hinge side trim pieces by removing side screws. Discard top piece, retainscrews.• Install one end

4For a complete food storage center,install a Monogram Freezer andRefrigerator side by side. Order ZUG75Unified Grille Panel Kit for one continuous 3/

Pub. No. 49-60055-3Dwg. No. 197D2785P00112-03 JR65160-01NOTE: While performing installations described in this book,safety glasses or goggles should b

5Installation At End-of-RunFramelessCabinetsNOTE: 1/2" thick side panels shown.Side panels can be any thickness.Add side panel thickness to outsi

6Trim kitdescriptionsZGC2 – Provides 1/4" grille panel frame side pieces for83-1/2" and 84-1/2" installation heights. The suppliedgrill

7ZIR36N RefrigeratorZIF36N Freezer Design InformationDesigned to be installed flush or semi-flush withsurrounding cabinetry. Cutout dimensions, cleara

8Custom Door Panel Dimensions Using Standard Trim1/4" thick panelsorPanels secured to 1/4" thick backingZIR36N RefrigeratorZIF36N Freezer• 1

9ZIR36N RefrigeratorZIF36N Freezer• The ZKTR36LH (or ZKTR36RH) trim kit provides for theinstallation of 3/4" thick custom door and grille panels,